1977 OPC Star Wars #58 Harrison Ford as Han Solo — Raw

Centering estimate: left border ~10px, right border ~18px, top border ~12px, bottom border ~20px — approximately 65/35 left-to-right and 65/35 top-to-bottom, noticeably off-center favoring left and top. Blue border shows visible chipping and wear along all four edges, most pronounced at the bottom and right edges. All four corners appear rounded to varying degrees — top-left and bottom-right show the most rounding, consistent with a VG to VG-EX range. Surface shows some scuffing and gloss loss across the image area; no obvious hard crease is confirmed from this scan but lighter surface creases or handling lines cannot be ruled out. OPC stock and bilingual caption are consistent with the expected card; printer confirmation is supported by the French text visible in the caption.

Centering: left border appears noticeably wider than right (roughly 65/35 L-R favoring left), top and bottom borders appear closer to 55/45; centering is acceptable for a 5-6 range. Blue border shows visible chipping and wear along the left and bottom edges, consistent with the known fragility of 1977 OPC/Topps blue-series borders. Corners appear lightly to moderately rounded — at least two corners (bottom-left and bottom-right) show soft rounding visible even at this resolution, consistent with EX to VG-EX range. Surface appears to retain reasonable gloss with no obvious creases visible in the photo, though a single-angle seller photo cannot rule out light surface creases or staining. The blue border chipping and corner wear are the primary grade suppressors here, pointing toward a PSA 5 (EX) most likely, with a ceiling of 6 if corner wear is milder than it appears and a floor of 4 if reverse shows additional wear.

Centering appears roughly 60/40 left-to-right and 55/45 top-to-bottom — not a concern here as damage dominates. The seller explicitly discloses 'multiple creases' and 'corner wear,' both of which are visible or strongly implied in the photo: the surface shows stress lines consistent with multiple creases, placing this squarely in the PSA 2–3 range. All four corners show visible rounding and wear consistent with at least VG-level handling; the blue border shows chipping typical of this series. Gloss loss is evident across the face. A PSA 3 (VG) requires a visible crease but corners not fully blunted — given the self-disclosed 'multiple creases,' PSA 2 (GOOD) is the more likely outcome; I cannot rule out a low 3 if the creases are lighter than they appear. OPC versus Topps cannot be confirmed from the front image alone, though the bilingual caption text is visible and confirms OPC.

Centering estimate: left border appears slightly wider than right (approximately 55/45 L/R), top border slightly wider than bottom (approximately 55/45 T/B) — centering is acceptable for a PSA 6-7 range. Blue border chips are the primary concern on OPC issues; at this resolution the borders look relatively intact with no obvious heavy chipping, but the blue borders on OPC stock are notoriously fragile and micro-chipping is hard to confirm without a higher-magnification image. Corners appear to have light wear — they are not razor-sharp but not visibly rounded, suggesting EX-MT territory. Surface gloss appears present with no obvious creases or print defects visible, and the image is clean. Back condition, edge wear, and true corner integrity cannot be fully assessed from this single front scan, warranting the wider range of 5–7.

Centering: left blue border appears slightly wider than right (approx 55/45 L/R), top border marginally wider than bottom (approx 55/45 T/B) — centering is acceptable for EX-MT range. Blue border shows some chipping/wear on at least two visible corners (lower-left and lower-right appear softened/lightly rounded), consistent with a 6 EX-MT grade; upper corners are harder to assess at this resolution. Surface gloss appears decent with no obvious creases or staining visible, and print quality looks clean with no significant snow or marks on the image area. Corner wear is the primary grade limiter here — if the upper corners prove sharper on inspection a 7 NM is possible, but visible lower-corner softening makes 6 the most likely PSA equivalent; a hidden back-side issue or heavier corner rounding could push this to 5 EX.